拆卸和安裝約翰迪爾燃油系統(tǒng)高低壓調(diào)節(jié)閥、燃油切斷電磁閥故障診斷測試及相關(guān)部件拆裝技巧
Remove and Install Low Pressure Regulating Valve
1. Close fuel shut-off valve, if equipped.
NOTE: On high fuel tank applications without fuel shut-off valve, fuel tank return line must be pinched before disconnecting, then plugged,
2. Disconnect fuel tank return line from filter housing and drain fuel into clean container.
3. Remove low pressure regulating valve parts (A—G).
To remove valve seat (B), use a standard wire tie strap with approximate 5/16 x 3/16 inch square head. Insert tie strap head through bore of valve seat, rotate to  catch lip of seat and remove seat.
4. Clean and inspect all parts. Replace all O-rings and seals.
Low Pressure Regulating Valve
5. Install parts in reverse order.
Install valve seat (B) (O-ring end first) into bore of filter housing. Make sure it is firmly seated in  bore.
A—O-Ring B—Valve Seat
Valve Components
Install seal (D) with tapered edge of seal into lip of regulating valve (C).
Spring (E) is color coded red, identifying it as the low pressure spring.
Tighten valve housing (G) to specifications.
—Low Pressure Regulating Valve D—Seal
E—Spring, Low Pressure (Color Coded Red) F—O-Ring
G—Valve Housing
Specification
Low Pressure Regulating
Valve-to-Filter Housing—Torque .....................................  18 N•m (13 lb-ft)

Remove and Install High Pressure Regulating Valve
1. Close fuel shut-off valve, if equipped.
NOTE: On high fuel tank applications without fuel shut-off valve, fuel tank return line must be pinched before disconnecting, then plugged,
2. Disconnect fuel tank return line from filter housing and drain fuel into clean container.
3. Open valve on water separator bowl and drain filter housing.
4. Remove fuel temperature sensor (F). See REMOVE AND INSTALL FUEL TEMPERATURE SENSOR in Group 110.
5. Remove high pressure regulating valve (C).
6. To remove screen (A), see REMOVE AND INSTALL 100 MICRON INTERNAL FILTER HOUSING SCREEN INSERT next in this Group.
NOTE: High pressure regulating valve is not repairable. Do not disassemble valve. If defective, replace entire assembly.
7. Clean and inspect all parts. Replace all O-rings.
8. Install parts in reverse order.
If removed, install screen (A). See REMOVE AND INSTALL 100 MICRON INTERNAL FILTER HOUSING
SCREEN INSERT next in this Group. Tighten regulating valve to specifications.
High Pressure Regulating Valve
A—Screen B—O-Ring
C—High Pressure Regulating Valve D—O-Ring
E—O-Ring
F—Fuel Temperature Sensor
Specification
High Pressure Regulating
Valve-to-Filter Housing—Torque .................................. 14 N•m (124 lb-in.)
9. Install fuel temperature sensor (F). See REMOVE AND INSTALL FUEL TEMPERATURE SENSOR in Group 110.
10. Add fuel to filter housing between minimum and maximum marks on housing. Fuel can be added by throttling the fuel shut-off valve (if equipped), or by removing cover and adding fuel from a clean container.

Remove and Install 100 Micron Internal Filter Housing Screen Insert
1. Remove fuel temperature sensor (F). See REMOVE AND INSTALL FUEL TEMPERATURE SENSOR in Group 110.
Remove high pressure regulating valve (C). See REMOVE AND INSTALL HIGH PRESSURE
REGULATING VALVE earlier in this Group.
IMPORTANT: If allen wrench is pushed too far into 10 micron screen during removal and installation, screen may be damaged.
Tie a rubber band (K) approximately 10 mm (3/8 in.) from end of allen wrench, as shown, to prevent screen damage.
NOTE: Screen is approximately 91 mm (3-5/8 in.) up in bore of filter housing. Use a long allen  wrench.
2. Attach a rubber band (K) on end of 5 mm allen wrench and remove 10 micron screen (A) from filter  housing.
3. Clean and inspect screen.
4. Using allen wrench with rubber band, install screen in filter housing and tighten to the following specification.
Specification
100 Micron Internal Filter Housing
Screen—Torque ............................................................... 5 N•m (44 lb-in.)
High Pressure Regulating Valve
5. Install pressure regulating valve parts (B—D). See REMOVE AND INSTALL HIGH PRESSURE REGULATING VALVE earlier in this Group. Install fuel temperature sensor parts (E) and (F). See REMOVE AND INSTALL FUEL TEMPERATURE SENSOR in Group 110.
Remove Screen
A—100 Micron Screen B—O-Ring
C—High Pressure Regulating Valve D—O-Ring
E—O-Ring
F—Fuel Temperature Sensor K—Allen Wrench with Rubber Band

Remove and Install Fuel Filter Check Valve
1.  Close fuel shut-off valve (if equipped).
2. Disconnect fuel line (shown disconnected) and remove check valve (B). Remove O-rings (A) and (C) from both ends of check valve.
3. Install check valve in filter housing and tighten to specifications.
Specification
Fuel Filter Check Valve to Fuel
Filter Housing—Torque ...................................................  33 N•m (24 lb-ft)
4.  Connect fuel line and tighten to specifications.
Specification
Fuel Line-to-Fuel Filter Check Valve—Torque.................................................................  24 N•m (18 lb-ft)
5.  Open fuel shut-off valve.

Remove and Install Primer Pump
1. Remove primer pump (A).
2. If required, remove adapter (B).
3. Clean and inspect parts.
4. Install primer pump and adapter with new O-rings and tighten to specifications.
Specification
Fuel Primer (Single Rail Fuel Primer Pump
System)—Torque.......................................................... 14 N•m (124 lb-in.)
Fuel Primer-to-Fuel Filter Housing A—Primer Pump
Adapter (Single Rail Fuel B—Adapter
System)—Torque............................................................ 11 N•m (97 lb-in.)

John Deere Qianglu engine parts supply r515454 gasket, John Deere Qianglu engine parts supply re522589 heat exchanger, John Deere Qianglu engine parts supply re28429 filler cap, John Deere Qianglu engine parts supply re503664 support, 0001369020001369025 0001369201 0001371004 00013710000001371006 0001371007 0001371008 00013710000001371012 0001371014 0001371017 0001371010001371019 0001371020 0001372001 John Deere Qianglu engine parts supply az103850 bearing, John Deere Qianglu engine parts supply az103733 hub, John Deere Qianglu engine parts supply re526662 oil pump kit, John Deere Qianglu engine parts supply r123471 housing, Bosch f00n203165 overflow valve, Bosch f00n203165 overflow valve, man 51111070032, Delphi l221pbc injector, Volvo 20430583 injector, Delphi ljrb06005a injector, Perkins 4545091 injector, Carter 3202d excavator, M11 injector plunger 3411711, Cummins metering plunger 3411711, Shangchai fuel injection pump assembly s0000061 + 02, electric 294000-1810 fuel injection pump, 294000-1811, Bog Warner e3840028020a0 exhaust gas recirculation valve, e3840028020a0 exhaust gas recirculation valve, r79604, r79605, r79606, re15807, re15808 pipe nut, John Deere Qianglu engine parts supply r175593 pressing plate, John Deere Qianglu engine parts supply re521248 filter element, John Deere Qianglu engine parts supply re520842 filter element, bog Warner e3840034806a0 exhaust gas recirculation valve, e3840034806a0 exhaust gas recirculation valve, Borgwana e3840064811a0 exhaust gas recirculation valve, e3840064811a0 exhaust gas recirculation valve, Volvo 20734268 water pump, Volvo 20734268 water pump, voe20734268 water pump, Kubota 1j500-53050 injector, Kubota 1j500-53051 injector, 1j50053050, electric 095000-9690 injector, electric 095000-9691 injector, electric 095000969120673 injector, sdanai 20673 injector, Qianglu 20673 injector, 22205 injector, sdanai 22205 injector, Qiangli 22205 injector, 22808 injector, sdanai 22808 injector, Qiangli 22808 injector, 22817 injector, sdanai 22817 injector, Qiangli 22817 injector, 26632 injector, sdanai 26632 injector, Qiangli 26632 injector, John Deere Qiangli engine parts supply yc27704 steering control spring, John Deere Qiangli engine parts supply yc27705 header lifting control spring, John Deere Qianglu engine parts supply re522878 filter element, John Deere Qianglu engine parts supply re509672 filter element, and John Deere Qianglu engine parts supply re541922 filter element,